Industrial Equipment1

Our company is offering AC Servo Drive, which are a closed-loop integrated system with speed and torque control mode. These are equipped with built-in protection circuits against any overload, input over voltage and any motor connection error (wrong encoder wiring, phase-phase and phase-ground short-circuit).

Features:

• 
  Closed-loop integrated system with speed and torque control mode
• Scale factor that can be set by the user on both analog and frequency inputs and on the repetition of the encoder signal
• PNP/NPN/Differential frequency interface, with digital filter that can be configured by the user for noise immunity
• Integrated management of over travel signals
• Built-in fully automatic notch filter to remove the system’s resonance frequency
• Control: with analog signal (proportional to Speed or Torque). Optically coupled digital control I/O.3 inputs and 2 outputs with user-defined functions
• External regenerative resistor provided with sensing for maximum temperature alarm (optional) 200VAC to 230VAC Power Supply [+10%; –15%], single-phase or three-phase (can be set by operator)
• Power sections kept separated for logic/signal and power electronics
• Built-in protection circuits against any overload, input over voltage and any motor connection error (wrong encoder wiring, phase-phase and phase-ground short-circuit)
• Dynamic braking circuit activated when the power section is not powered or in case of alarm

Send Enquiry

With the help of our efficient experts, we have been able to supply a wide range of PWM DC Servo Drives, which have a capacity up to 250 V DC and 100 A. The PWM close loop control technology offers higher reliability and accuracy in positioning applications. Our range is equipped with state-of-art MOSFET based power amplifier cards of this drive improves the performance of the drive and the plug in type pre-driver section on the power card make the power cards easily serviceable.

Features:

• These drives are sturdy, simple and very easy to use
• The over current protection, under-over voltage protection, drive Inhibit function and a potential free monitor voltage relay ( MVR) available with this drive, really assures hazard free smooth operation

Send Enquiry

Our company is engaged in supplying Twin Comparator, which are a twin channel electronic compactor with an rs232c output. It has a sturdy, splash – proof and ergonomic design, which makes it the ideal compactor for the harsh shop floor environment.

Features:

• Two independent measuring channels a & b with selection of combinations +a, -a, +b, -b, +a+b, +a-b, -a+b & -a-b
• 2 metric and 2 inch measuring ranges; metric ranges: +/- 200 & +/-2000um
• Resolution: 0.1 & 1um inch
• Ranges: +/- 0.020 & +/- 0.200 inch
• Resolution: 0.00001 & 0.0001 inch
• 3 ½ digit large bright red led display
• Red, green & yellow tolerance lamps for undersize–ok–oversize indication
• RS 232c data output
• Externally accessible zero and calibration controls
• Suitable for half–bridge type inductive probes
• Sturdy, ergonomic, metallic body
• Splash proof and sealed against dust
• In–built 110v/220vac mains selection

Send Enquiry

Our range of Multigauge Inspection System MGS-01 consists of a Main CPU unit, and Operator Interface Panel. These have a modular construction allows for system up-gradation and easy maintenance.

Main CPU unit Part No.: MCU1

• Contains Processing Software · Accepts inputs from up to 32 probes
• Compares the results with the hi an low limits and indicates alarms
• Serial Communication Port for PC interface (RS232 interface)
• Parallel Printer Port · Data Storage
• Real Time Clock

Probe Interface Module (PIM) Model: MGS-01

• 
  Has the necessary electronics to condition the output of a LVDT analog probe
• Has a local keypad for probe offset adjustments
• PIM conditions and coverts the probe output for use by Main CPU and indicates the actual reading of an individual probe
• Has three LED indicators Red – Reject, Green – OK, Yellow – Rework
• Has Buzzer for failure / reject condition

Operator Interface Panel (OIP) Part No.: OIP

• This module has a keypad and LCD display (text display).The required readings (e.g. pre-programmed algebraic relations between PIM1, PIM2 and PIM4) are indicated by this display.
• Algebraic relations among different inputs (from probes) are programmed, Processed and indicated on the digital display
• This module has a LCD graphic display.
• Apart fro algebraic functions of an OIP, it has graphic screens for pie charts, Cpk, standard deviation, high, low alarms

Digital Input / Output Module (DIO) Part No.: DIOM

• This Digital Input Output Module enables the MultiGuage Inspection System (MGS-01) to interface with the outside world. It provides 8 general purpose bidirectional input/ output lines

Send Enquiry

Our company is engaged in supplying CNC Controllers for Lathe Machine, which are a compact, low cost, computerized numerical control for metal cutting machine tools and other equipment requiring positioning and contouring axes. These offer an easy-to-use, cost effective motion control for a wide variety of manufacturers.

Technical Specifications:

• Control of up to two axes plus spindle. Feedback Inputs: 4 (2 axes+Spindle+MPG)
• 8" green CRT display(optional 9"). Analog Outputs: 3(2 axes+Spindle). 2D linear and circular interpolation
• CMOS RAM memory for storing MSD, Tool Data, "M" functions and part programs (32K)
• High resolution for high accuracy. Control resolution is 0.001 mm/0.0001 inch.
• Self-charging battery for memory retention up to one month
• MSD parameters may be entered using keyboard or from a PC using serial port.
• MSD parameters are displayed in an easy-to-read menu for simple selection and entry.
• Standard and Parametric Subroutines, user defined Canned Cycles. BCD Output for M2 functions and T2 functions.
• Spindle Creep command for gear and tool changes. Program entry in ISO code & Assisted program entry.
• Math functions, conditional jumps. RS232 (V24) port for PC communication and DNC.
• 32 tool offset files (length and wear compensation, Programmable Feed Rate and Spindle Speed.
• Location code and tool radius. Number of Main Programs:250
• Internal feedback multipliers facilitate various Feedback resolutions of: 0.001 mm, 0.002 mm, 0.0025 mm, 0.005 mm 0.01 mm per pulse or 0.00005 in, 0.0001 in, 0.0002 in, 0.00025 in, 0.0005in, 0.001 in per pulse.

Other Information

• Pay Mode Terms: T/T (Bank Transfer)

Send Enquiry

Our company is engaged in supplying CNC Controllers for Milling Machine, which offer an easy-to-use, cost effective motion control for a wide variety of manufacturers. These have optical encoder or scale feedback operation and are a compact, low cost, computerized numerical control for metal cutting machine tools and other equipment requiring positioning and contouring axes.

Technical Specifications:

• Control of up to four axes plus spindle.
• Feedback Inputs: 5 (4 axes+MPG).
• 8" green CRT display (optional 9").
• Analog Outputs: 5(4 axes+Spindle).
• 3D linear, 2D circular interpolation, Helical Interpolation.
• CMOS RAM memory for storing MSD, Tool Data, "M" functions and part programs (32K).
• High resolution for high accuracy.
• Control resolution is 0.001 mm/0.0001 inch.
• Self-charging battery for memory retention up to one month.
• MSD parameters may be entered using keyboard or from a PC using serial port.
• MSD parameters are displayed in an easy-to-read menu for simple selection and entry.
• Standard and Parametric Subroutines.
• Standard and user defined Canned Cycles.
• BCD Output for M2 functions and T2 functions.
• BCD Output for S2 or S4.
• Geometric aids simplify programming..
• Optical Encoder or Scale feedback's On, Jog Mode, Thread cutting On, Axes Enable.
• Graphic programming assistance Emergency and Reset Outputs.
• DNC/Simultaneous programming.
• Optical Encoder or Scale feedback Operation.
• Metric or inch feedback is selectable by MSD.
• Manual data entry via keyboard.
• Internal feedback multipliers facilitate various Feedback resolutions.

Send Enquiry

Our company is engaged in providing CNC Retrofitting of manual machines to CNC. This include the entire procedure of reconditioning, designing and manufacturing new drive system with fitments, designing, manufacturing suitable electrical panel and interface of CNC controls.

Features:

• We also provide requisite products like CNC controller, AC Servo Drives, DC Servo Drives for second hand CNC machines
• This ensures that you are not required to change the entire CNC package, reducing the cost as well as the commissioning time
• Our CNC controller can easily replace old models of CNCs (like Kirolskar – Crusader, Viking, Siemens 3T )

Send Enquiry

We are offering a wide range of Programmable Logic Controller, which is compact, modular type and cost effective PLC. These are designed to withstand harsh industrial environments in industries. These have front end termination for easy installation and an intelligent user friendly programmer-ARI ONE.

Features:

• Processor based PLC
• Enhanced Boolean instruction for Ladder
• Comprehensive self diagnostics for CPU & I/O's
• Serial communication for intelligent interfaces
• User configurable I/O bus
• Wide choice of rugged I/O'
• Modular concept
• Front end termination for easy installation
• Intelligent user friendly programmer-ARI ONE

Strong hardware features

• Detection of CPU Error, low battery indication, program mode, RUN mode indication.
• Watch dog timer.
• Easy to read I/O status.

Programming features

• Inexpensive, compact, user friendly compact programmer-ARI ONE.
• LogicSoft ladder development package used for editing/modifying ladder and monitoring of i/o status.
• Ladder software is driven by interactive menu through dynamic soft function keys.
• Configuration of I/O modules done through software.

Summary of the product

• (I) SOFTLOG PLC-MODEL ODYSSEY 2.
• CPU Module.
• Base Unit-32I, 16O.
• Expansion I/O-32I, 16O or 24I, 24O.
• Single axis controller card.
• Communication-RS232/RS485.
• Operator Panel-Useful for programming external timers/counters, error messages etc.

Send Enquiry

Our company is offering a wide range of PLC with Bi-Directional Ports, which can programmed as digital input or digital output. The Basic PLC unit has in all twenty-four such programmable ports. These have the latest micro controller technology that offers reliability to the performance of the PLC. Due to this bi-directional feature one can really get real flexibility at lower cost.

Features:

• The number of ports can be increased maximum up to 64 with the help of additional expansion modules
• MICROPOD PLUS can be easily programmed with a hand held programmer
• The 49 keys feather-touch keyboard and back lit LCD display make the PLC, a user-friendly tool
• PC based ladder diagram development and monitoring software package is also available.
• In addition to digital inputs-outputs, this PLC also has 8 analog inputs and 2 analog outputs
• This makes sensing, indication and control of various process variables such as temperature, pressure an easy possibility
• The in-built Real Time Clock makes all these controls possible on real time scale
• There is one High Speed Input available in this PLC, which can be used for some critical control for which minimum sensing time is required

Send Enquiry

Item Code: PIM-401

Our LVDT Signal Conditioners are procured from reliable manufacturers and have high accuracy ASIC that produces a low distortion. This ASIC also demodulates the signal from the LVDT sensor and converting it to a high accuracy, low noise signal, ready to interface with the highest accuracy A/D converter units.

Additional features:

• The LVDT signal conditioner unit is also insensitive to excitation level and excitation loading due to a state-of the-art ratio metric measurement technology.
• The LVDT excitation is measured at real time and the output is compensated in real time for any changes in excitation voltage level
• The PIM-401 can operate with almost any type of LVDT sensor available when writing those lines
• It's wide dynamic range (with wide range GAIN and DC Offcet controls) make it suitable for a wide range of LVDT sensors sensitivity
• The adjustment of these controls is very easy and can be done by the user using a small screwdriver
  
  Features:
  
  
• The LVDT Signal Conditioner unit is a stand-alone unit
• It is powered from +/- 15V DC (Other supply Voltage available on request)
• The LVDT transducer is connected to it via simple screw terminals (or screw terminals)
• The unit will output a voltage which is highly linear (0.05%) to the displacement (limited by LVDT sensor manufacturer's specifications)
• The unit has 5 digit 7-segment display
• Counting resolution: 1 micron
• Has RS232 output
• Has 0 to 2Vdc analog output
• Also available for 2, 4 or 8 probes
• Max. 32 probes can be stacked
• Item Code: PIM-401

Send Enquiry